• OilresidualAfterSeparation:≤2PPM
• WorkingTemperature:<120℃
• InitialDifferentialPressure:≤0.02Mpa
• ServiceLife:6000-8000h(StandardPressureAnd WorkingConditions)
• Installation:Vertical,horizontal
• AirFlow:Inlet,Outlet

• ImportedHVairfiltermediahasthefeatureofsmoothsurface,lowquantitation, finefibre,superfinefibre,smallaperture etc.
• Smalleranddenserfiltermediaaperturemeansmuchmoreoverlappedlayer; higherefficiency,morestableperformance,moredustcollected,andlonger servicelife.

Remove water scale,
keep machine smooth
Apureda UC-W205 water scale flusshing oil can remove the wawter scale, rust
and foreign substance, which will improve cooling efficiency.Special formula
will protect the metal, cooper and stainless steel materials.

     Advantages

• Suitable for heat exxchange, ccooling towers & machine and water pipe systems.
• It is safe and do not corrode metal.
• Remove water scale quickly. Normally, several hours will remove the foreign substance.
• It can dilute to use according to the machine status which will save cost.

• If it enters the eye accidentally, please wash it withflushing water and go too the hospital for treatment.
• the original liquid has irritating effect on the skin.Please wear protective quipment while using it.

Apureda UC-V205 is higher efficiently flushing oil ehich does not need heat
and stir vefore using. It has strong penetration force to wash the carbon
deposit without labor and foreign force. It also washes the small parts gap 
and does not damage the machine precision.



       Advantages

• Strong penetration and peel force can remove carbon deposit and oil mud efficiently.
• Wash compressor host nachine, oil pipe and heat exchange cerbon deposit quickly.
• Use eassilly, just immerse for 20minutes to 2 hours as per the dirt level.
• Do not corrode metal parts.
• One time can wash different parts and can repeat to use it.

• If it enters the eye accidentally, please wash it with flushing water and go to the hospital for treatment.
• The original liquid has irritating effect on the skin.Please wear protective equiipment while using it.

• The flushing oil is 3%-5% according to the compressor lubricant.That is, if the compressor lubricant is 100 liters, the flushing oil needs 3 to 5 liters.
• Aadd flushing oil into the compressor directly and run at least 24 hours.
• Disvharge used lubricant and flushing oil, then add new compressor lubricant.

• Please adjust the volume as per the carbon deposit level and monitor the cleaning process.We recommend you to ask professionals to do it.
• Please discharge all lubricants while the oil is heat to avoid precipitate.
• Do not recommend PEG and PET compressor oil to use it.

5 years effort,
Fortune global 500 Dow Chemical developed screw air compresor innovated lubricant.
Ucon^TM Air Compressor Lubricant S-6 is based on the PAG oil of Dow Chemical with other lubricants advantages to develop reliable
and compatible aynthetic oil.
Ac S-6 lubricant is free of macro-molecule during running.Then carbon deposit coking will be decreased.

Restrain coking and carbon deposit

Dow Chemical S6 compressor synthetic lubricant
is special fluid, it can effectively restrain and removve precipitate
to protect the machine well. Then it will avoid coking and
carbon deposit during running.














 

Longer service life

The air release property of S6 synthetic
lubricant is less than one minute, which will
decrease the contact time & area with air. Then
it will improve the machine heat and lubrication
efficiency to avoid hhigh temperature oxidation
process.

Lower maintance cost

• Cooler

• Air end screw

• Air oil separator

Typical Property

Typical air compressor installation


Typical condensate management installation


Traditional separator - with gravity pre-separation


Traditional separator - with gravity pre-separation

This is a traditional oil/water separator

It is a complex construction, made from many parts.
The principal of operation requires it to perform a series of processes on the condensate;
the effectiveness of each stage affects the performance of the next one.
If any one stage performs badly,the overall result is affected.














Traditional separator - with gravity pre-separation
 

If the filter is carbon, it must be soaked in water before installation, or its performance will be a small fraction of the rated capacity.

If oil contamination is higher than expected(high condensate flows or oil separator failure)carbon quickly becomes ineffecctive and flow is blocked.

This type od separator is usually fitted with an alarm to warm of high liquid levels caused by blocking in the separator - because that's what happens!
 

Effective treatment of oil-contaminated compressor ondensate for compressed air system.
Ensure a steady down slope from the outlet point to foul drain.Never discharge to storm drain or surface water.
Test outlet quality weekly usingg kit provided.Replace filter before outlet cloudiness exceeds the limit for your refion.

Water separator 60 to 7000 cfm (1.7 to 200m³/min)

SEP 3500 / 7000 ST

This is SEP 3500 ST and SEP 7000 ST
Large capacity single separators are more efficient than using multiple installations of samaller units.

Multiple installations are expensivve to engineer, and it is almost impossible to ensure that each separator receives an equal share of condensate.The service interval is  therefore ALWAYS dictated that the other are never fully utilised.
End-of-life replacement requires a new IBC,pre-filled with STERLING material.
The pressure relief chamber and connecting pipt-work is re-used.The contaminated material in the old IBC is sealed for transport to a licensed waste disposal site.Servicing is therefore both quick and clean.
Always refer to SEPURA before accepting an order - sample and site information may be needed.
Sizes are 600 litres (SEP 3500 ST) and,1,000 litres (SEP 7000 ST)



 

A complete range for all application sectors

The VITO high pressure range is available with a wide range of flow rates from
100m³/h (59cfm) to 6,000 m³/h (3,534 cfm).
The VITO LP low-pressure range is instead available in flow rates from 600 m³/h
(353 cfm) to 2,100 m³/h (1,237 cfm).

Energy efficiency

Since its launch on the market, the VITO has marked the beginning of a ''new ara''
in the world of air compresssion for blow molding machines; a qualitative leap,
offering greater efficiency together with a reduction in energy coats.In particular,
in the case of  a VITO frame M compressor, the wnwrgy consumption is decreased
by 16%.

Advantages

• Power surges are prevented when the motor is started
• The line flow rate is automatically adjusted
• Operation is continuous and no longer intermittent
• The regulation of the speed (and threfore of the flow)is continuous and in the range 30% - 100%.

0-50-100% : Modulation of the flow rate

If the request for compressed air decreases,the 0-50-100% device works by excluding the upper
effect of the first stage cylinder,by means of pneumatic valve unloaders,and therefore obtains a flow 
rate equal to 50% f the nominal value.Excludingg both efffects(ipper and lower) of the first stage cylinder,
the flow rate is deleted (0%).

Advantages

• Automatic reduction of flow rate and electrical consumption
• Reduction in the number of control valves and increased reliability of the compressor
• Optimization of flow rate regulation.

Optimized consumption : Energy Saving Pack
To implement the best solution,it iss necessary to know precisely the actual use of the compressor in order to study define the most efficient working
method for the system.
The Energy Saving pack includes an analysis of the energy consumption (energy audit) which can be followed by a corrective proposal for the 
installation of a control panel or a control panel with a VSD.
The main control panel can mange up to 8 compressors simultaneously.The panel constantly calculates the total compressed air flow rate and the
comsumption of electrical energy and makes it possible to adapt the compressor's work to the requested changes in real time.

 

Heat recovery

The thermal energy produced by the compressor can be recovered for different purposes at the
customer's plant (heating and auxiliary system).Depending on the compressor model,the thermal
power recovery is between 30% and 80% of the compressor power and water ccan be supplied 
at a temperature up to 90^°C.












HIGH PRESSURE - 40 bar (g)

Product range
Low pressure compressor